€3.15, Starting at Note: Tolerance of .125” will be automatically added to each dimension. The adapter kit in Table 1 contains all items needed to adapt one sliding rail kit needed to mount one Firepower 8000 Series 1U or 2U device in a rack. AV/Telecom/and IDF from my experience seem to have round holes just because the people who deal with them don't want to both with the adapaters and most items on not on rail kits. Read the publication. Get the tools for the square and they'll be good. €3.69 Warning Verify that there is sufficient screw engagement in the rack rail if using washers. Download 2U Adapter Kit Installation Instructions, Download 2U Adapter Kit Dimensional Drawings, Starting at Figure 2 Adapter Attachment to Slide Ends. Mount the slide rails in the rack by attaching the adapters to the rack rails/vertical mounting flanges. Our adapter brackets are highly configurable tools that allow users to make mounting equipment of any depth work in almost any rack. Skip to the beginning of the images gallery. Figure 3 Slide Attachment to Rack Rail/Vertical Mounting Flange. Installing Round Hole Adapters for Square Hole Rack Slides for the Cisco Firepower 8000 Series Last Updated: May 27, 2015 This document describes how to install round hole rack adapters that can be used to adapt the square-hole-only sliding rail kits that are supplied with the Cisco … Desired Width. Table 1 Round-to-Square Hole Rack Adapter Kit for Firepower 8000 Devices, 8 x 10-32 x ¼” (6.35mm) Philips pan head screws, 4 x M5-0.8mm x 15mm Philips pan head screws, Figure 1 Round-to-Square Hole Rack Adapter Kit for Firepower 8000 Devices. Your kit should look similar to the kit in Figure 1. The brackets themselves are 2U in height, but can be combined to mount up to 7U equipment safely. These are generally used in the sheet metal fabrication trades. Installation of the adapters and slide mounts to the rack is performed in two stages which are described in the following sections: Step 1 Slide the yellow retention piece away from the end (see “1” in Figure 2). 70 Square Inches to Circular Inches = 89.1268: 2 Square Inches to Circular Inches = 2.5465: 80 Square Inches to Circular Inches = 101.8592: 3 Square Inches to Circular Inches = 3.8197: 90 Square Inches to Circular Inches = 114.5916: 4 Square Inches to Circular Inches = 5.093: 100 Square Inches to Circular Inches = 127.324 Step 5 Tighten the screw (see “5” in Figure 2). This may be managed with washers. Recommended double relay rack spacing, 23.8" - 33.2" (measured from front to back of the rack's mounting surface), EIA 3/8" square holes (9.5 mm) to attach to rack, Round holes or 12-24 threaded holes to attach to Rapid Rail. This kit has an assortment of brackets that can be configured in multiple ways to solve most common installation issues, Kit includes 2 of each bracket (10 total), Weight capacity rated at 50 lbs per rack unit, Compatible with Dell PowerEdge 8450, 2850, 2650, 2550, 2450, Compatible with Dell PowerVault 122T, 132T, 220, 221, 224F, 660F, 4post cabinets (Chatsworth MegaFrame, Great Plains, Shark and most other racks), Double 2Post frame (Homaco, APC, and others). Adjusts server rack installation depth A solution to mounting equipment that is too long or too short for your rack Converts round holes to square holes Kit includes 2 of each bracket (10 total) Weight capacity rated at 50 lbs per rack unit Works on 4 post racks with square, round and threaded holes Ex: 1U = 50 lbs, 2U = 100 lbs, 4U = 200 lbs, 6U = 300 lbs, etc. Step 2 Place the square holes over the mechanical catches at the end of the slide (see “2” in Figure 2). Use with other racks and slides is not supported and may cause injury or damage to equipment. The rail/vertical mounting flange goes into the C shape (from above) of the adapter (see “2” in Figure 3). Desired Height. Longer screws will not tighten properly. The rails must be threaded with 10-32 holes to use the provided screws. Square are ok when you have the tools. Step 2 Line the end of the slide (with the attached adapter) to the holes. Rack Conversion Guide: Square-to-Round-Hole Rail Adapter Overview Supermicro quick-release rails are designed for use in racks with square holes. Universal Metals. Install brackets (hardware not included) in the space where the rack needs to be extended or reduced. For the best experience on our site, be sure to turn on Javascript in your browser. The document contains the following sections: Warning This document applies only to sliding rail kits that have yellow square hole mount retention pieces. For the best experience on our site, be sure to turn on Javascript in your browser. Your kit should look similar to the kit in Figure 1. The brackets themselves are 2U in height, but can be combined to mount up to 7U equipment safely. Warning Use of non-supported racks or hardware may cause the equipment to fall, which could result in equipment damage or personal injury. 1. Our adapter brackets are highly configurable tools that allow users to make mounting equipment of any depth work in almost any rack. User supplied screws may be used, provided that they do not exceed the ¼” (6.35mm) length. Firepower 8000 Series 1U or 2U device in a rack.